Kolmivaiheisten sähkömittareiden asennus ja käyttö-
1. Mittari on tarkastettu ja sinetöity ennen tehtaalta lähtöä, ja se voidaan asentaa ja käyttää. Jos lyijytiivistettä ei ole tai se on ollut varastossa pitkään, asianomainen osasto on kalibroitava ja suljettava uudelleen ennen asennusta ja käyttöä.
2. Mittari tulee asentaa pystysuoraan eikä vinoon kuivaan ja tuuletettuun paikkaan. Pohjalevy, jolle mittari on asennettu, tulee kiinnittää tukevalle ja tulenkestävälle-seinälle, jota ei ole helppo täristä. Mittarin korkeus on noin 1,8 m.
3. Kytke kytkentäkaavion mukaan, kiristä johtoruuvit ja kiinnitä liitäntälevy alapään kierrelaatikkoon.
4. Todellinen sähköenergialuku saadaan kertomalla ilmoitettu luku muuntajaan kytketyn sähkömittarin muunnossuhteella.
5. Yksi lomake ja yksi kortti: Käyttäjän hallussa olevaa IC-korttia ei voi vaihtaa. Jos se katoaa, se on mentävä sähkönjakeluosastolle (eli sähkönmyyntitoimistoon) ostamaan uusi.
6. Sähkön ostovalmistelut: Käyttäjän tulee laittaa IC-kortti kerran kortin pidikkeeseen, jotta taulukon tiedot voidaan lähettää takaisin tietokoneen tietokantaan.
7. Sähkön ostotapa: Kun myyt sähköä, aseta IC-kortti IC-kortinlukijaan, käytä tietokonetta samanaikaisesti ja salaa käyttäjänumero,-ennakkoon ostettu sähkö, kapasiteettirajoitusmenetelmä ja rajoitettu teho IC-kortti.
8. Sähkökortin käyttö: Aseta sähkönostokortti kortin pidikkeeseen. Jos kyseessä on kelvollinen kortti, mittari lukee tiedot automaattisesti mittariin ja LCD-mittarin näytöllä näkyy vuorotellen: sähkön osto, sähkön kokonaisosto, mittarin ajat, hälytyssähkö ja luottoraja, rajoitettu teho. Ota sitten kortti pois ja säilytä sitä kunnolla.
9. Käyttönäyttö: Mittarin käytön aikana LCD-näyttö näyttää vuorotellen mittarin jäljellä olevan tehon ja kokonaisvirrankulutuksen.
10. Overcapacity alarm: During the running process of the meter, if the "alarm indicator" flashes rapidly, it will warn the user that the overcapacity has been used; After that, the switch will be closed for 3 minutes, and the time to restore the power supply will be displayed in a countdown mode (180 seconds); if the user responds by inserting the card, the power supply can be restored immediately.
11. Hoarding limit: If the purchased electricity + remaining electricity > hoarding electricity (10000kWh), the purchased electricity will not be read in, the display will display the "remaining limit" prompt, and the electricity in the card is still valid.
12. Early warning reminder: When the remaining power in the meter is less than 2 times of the "alarm power", the "alarm indicator" will flash (with an interval of 1 second) to remind the user to purchase electricity. At this time, if the user responds by inserting the card, the "alarm indicator" "The blinking interval becomes 2 seconds, which can avoid the power failure warning.
13. Power-off warning: If the user does not insert the card to respond when the warning is issued, when the remaining power is the alarm power agreed by the user (or 10 percent of the power purchased this time), the meter will turn on the power-off warning and display "Turn off" At this time, insert the IC card into the card holder once to restore the power supply. If you can't find the IC card of this watch after the switch is turned off, you can borrow the neighbor's IC card and insert it to restore the power supply.
14. Power purchase reminder: When the remaining power in the meter is less than the "alarm power", the "alarm indicator" will be always on to remind.
15. Fault declaration: When the remaining power shows zero or negative value, it will display the "opening" prompt. If the meter continues to run, the user should purchase electricity immediately, and actively report the situation to the power supply department.
